Search the Community
Showing results for tags 'GT86 Forced Induction'.
Found 2 results
-
Hi everyone, Thought to start a thread where we can keep all the Avo news and info in one place Starting off with some great news .... new pricing for 2015 has been announced, reducing prices by approx 10% making the kits even better value Stage 1, Non Ceramic is £2799 + vat Stage 1, Ceramic is £2,999 + vat Stage 3, Billet Ceramic is £3,349 + vat Stage 4, Large Billet Ceramic is £3,699 + vat Stage 1, is capable of 260 - 290 bhp depending mainly on exhaust flow and choice of actuator. A stock exhaust will be around 260 and a nice 2.5" exhaust will max out around 290bhp. Maximum flow for this turbo is 380bhp. Stage 2, is simply the same as stage 1, but adds a 3" exhaust for higher output, 280 - 320bhp is possible depending on tune. Maximum flow for this turbo is 380bhp. Stage 3, uses a "Billet" compressor wheel in the same housing as stage 1, the billet wheel provides approx 20% increase in flow. We rate this set up as 280 - 440. This is the kit we used throughout 2014 on our GT86R, making 421bhp on stock engine and around 460 on a built engine. Maximum flow for this turbo is 470bhp. Stage 4, uses a larger Billet compressor wheel and larger turbine wheel with internal changes to the turbo for increased flow. Also included is larger intercooler and up pipe. Rated at 400bhp upwards. We will be testing this early next year and our target is 520 - 550bhp. Kit specifications are available on our website. Other Products Advised for all turbo kits: Breather System (199 + vat) 3 bar map Sensor & overboost fuel cut (89.95 + vat) Optional Upgrades for all kits: Electronic Boost Control (150 + vat) This includes the EBC valve, wiring and map upgrades using 10 custom race rom maps to allow closed loop boost control, boost is switchable via cruise control stalk and both throttle angle and gear dependant. Temperature safety maps are also included and boost is only allowed to increase if oil, water and air temps are within safe parameters. Dump Valve: There are a few options here, you can use an OE recirculating type available for £20 off ebay/scrappy etc. Or we have the Avo polished alloy one which can be configured as recirculating (quiet) or as a 50/50 for the whoosh! High Capacity Air Intake Kit Avo have developed their own airbox kit, crafted in carbon fibre and housing an induction type cone filter. The airbox includes a intake duct for cold air supply. More details soon. Exhausts: Avo exhausts are available in 2.5" & 3" depending on power goals, they are also available with or without cat, with or without resonators depending on exhaust note required. Anything else? Don't forget the stock clutch is all but useless when turbocharging, it is only just possible to use with the lowest spec turbo and even then its marginal! So factor in for an uprated clutch. Fitting Costs Turbo Kit Basic - install and map £750 + vat Turbo Kit + EBC, Clutch, Exhaust - install and map £995 + vat We'll update this thread with further news, pics and specs as we get them Any questions fire away Best Regards Adrian
- 35 replies
-
- Fensport
- Turbo GT86
- (and 6 more)
-
Hi Everyone, Just to let you know we now have a very affordable solution to upgrading your fuel system for forced induction owners High Capacity Fuel pump kit GT86/BRZ £110.70 + vat 246 Litres Per Hour Simple installation Complete with 'O' rings and in tank filter. Also a High Capacity Port Injector Set £299 + vat 540cc (We can also supply 660, 770 & 1100 cc Injector kits, please enquire) A complete set of 4 port injectors with wiring tails and necessary seals. Injector sets are precisely flow matched to within 1%. Each injector within each set is individually numbered and results for each injector are listed on a detailed flow sheet included with the set. Injectors are flow tested and rated at 43.5psi (3Bar) at 90ºF fuel temperature using CF-16B calibration fluid. Superior short pulse width control and tight manufacturing tolerances make these injectors easy to tune and provide great driveability. Every injector is covered against failure caused by defects in original manufacture by our 12 month warranty. The injectors require you to change the injector plug on the wiring harness. This can be done by soldering in the pigtails (included) to replace the plugs currently on your harness. This is our preferred method of install due to limited space in the injector area. Optional plug & play wiring adaptors are available to order. Best Regards Adrian
-
- GT86 Fuel System
- GT86 Turbo
-
(and 2 more)
Tagged with: